| |
New
Listings | Complete
Breweries |
Brite
Beer Tanks |
Brewhouses
| Misc
Fermentation
| Filtration
| Packaging Equipment | Refrigeration
| Malt Handling
| Distilling
FLOWSCALE
Consistent, accurate weighing
Consistent flavor of end product
Variable flow rates to match your mill
Add-on units for blended ingredients available
Automation from silo to mash/lauter tun
Units are adaptable to your needs
Reduced labor and operating costs
Efficiencies through bulk malt purchases
weighs the malt as it moves from bulk storage tank to the mill.
controls the rate at which the malt is ground in the mill.
sequences the starting and stopping of the malt handling equipment.
Accurately control any malt combination to within 1 percent of actual weight, even with variations in malt densities.
controls electronic relays to start and stop augers and every piece of the operation, in sequence, from the malt silo to the grist case or mash tun
Simple to install
requires minimal floor space — only 12" x 47" for
the basic unit.
Each additional unit uses only 9" x 47" of floor space.
FP 981-CF4 Continuous Flow FEEDPRO Ingredient Unit (Standard 4" weigh auger)
FP 981-CF5 Continuous Flow FEEDPRO Ingredient Unit (5" weigh auger)
FP 981-CF6 Continuous Flow FEEDPRO Ingredient Unit (6.5" weigh auger)
FP 981-CF8 Continuous Flow FEEDPRO Ingredient Unit (8" weigh auger)
FP 981-LIW Loss-in-weight FEEDPRO Ingredient Unit
INGREDIENT UNIT ACCESSORIES
CF AND LIW INGREDIENT UNIT OPTIONS
FI 090 Hopper top for auger fed CF unit, 4" inlet tube
FI 091 Hopper top for auger fed CF unit, 6" inlet angle ring
FI 093 Tube magnet for FI 091
FI 092 Single unit hopper top extension
FI 094 Double unit hopper top extension
FI 082 Hopper top for LIW unit (augered ingredient, with magnets)
FI 080 Manual load door for LIW unit
SN E2K Proximity Sensor for auger fed CF Units and to detect plugged gathering auger
SN E8K Special Proximity Sensor for CF units handling light material (soy hulls, bran, etc)
FI 163 Agitator for LIW units (for poorly flowing ingredients)
FI 060/63/64 Discharge chute for horizontal gathering auger, 3 1/2", 4", 6"
FI 211 Discharge Plenum for 1 unit, 6" angle ring
FI 212 Discharge Plenum for 2 units, 6" angle ring
FI 213 Discharge Plenum for 3 units, 6" angle ring
FI 173 Overmill mounting stand for up to 4 units, specify 37",40",43¼", or 46¼"
FI 071 Floor mount legs, set of 4, specify 38½", 40½", 43¼", or 46¼"
FI 071-X Custom Legs (specify length) Note: some lengths will need bracing
FP981-RLY Relay box with 8-position solid-state relay circuit board (with 2 inputs & 2 relays)
RY OAC5 Solid-state relay (max. 2 per metering unit)
RY IAC5 Solid-state input module (max. 2 per metering unit)
FI 860 CF8 single unit hopper top extension
FI 865 CF8 discharge plenum, 8" square to 6" angle ring
FI 880 CF8 support frame for up to 2 units, specify leg length
MOTOR CONTROL OPTIONS
MC 2430 Custom Motor Control Center - Estimate
Pricing: Contact us for quote
Picture 1 |
Picture 2 |
Picture 3 |
If you would like to be notified when a new listing is posted, please enter your email below.
|
|
